(SANITIZED) WORK RECORD

• Document Type: CREST
• Collection: General CIA Records
• Document Number (FOIA) /ESDN (CREST): CIA-RDP78-03424A000800030005-7
• Release Decision: RIPPUB
• Original Classification: S
• Document Page Count: 2
• Document Creation Date: December 22, 2016
• Document Release Date: February 15, 2012
• Sequence Number: 5
• Publication Date: January 21, 1958
• Content Type: FORM

j
Declassified in Part - Sanitized Copy Approved for Release 2012/02/16: CIA-RDP78-03424A000800030005-7
.
25X1
CONTRACT N0( RD-128, Task Order 3
CONTRACTOR
WORK ORDER NO. 1
ISSUE DATE 21 January 1958
Design, devalopm,,,nt
and fabrication of a
JOB TITLE parabolic dish antenna
PRICRITY tiC. 1
PREMIUM PAY
TOT ~~:',Crn
c., a Ai., $6142.12
CON^.:RACTORS I STIMMA';'ED 71iWLETIC''' DA E co da-?s after recaipt of order
40,DESCRIP`iI4;;: Design, dev~,1c , and fabricate a reflector pedustal assembly
an. a Instructions to t,'-1L, contractor appear on the
attachuien to this Work Order No.l.
The association of tad contracting organization with this c,ntract and/or
equipment is classifi.d SECRET.'
EQUIP NI. SECURI ': CLASSIC 1U UNCLASSIFIED
1S ignature)
DATE COMPLETED
WORK ASSIGNED BY
REQUESTING DIVISION APPROVAL
ENGINEERING DIVISION APPROVAL
CONTACT FOR REQUESTING DIVISIO?'
t*
COGNIZANT COMPANY CONTACTS: TECHNICAL
TSLgnature 1,
PHONE
BLDG. & ROOD1
ADMINISTRATIVE
tlfh UV OATS by
TYPI
te- !
$1it9 cuss PAIRS RRtl GLASS
JUST 22, --- six" isv 2tt.E._ AuTU, NA IF!
T 4.
CONFIDFN'TIAL
25X1
25X1
Declassified in Part - Sanitized Copy Approved for Release 2012/02/16: CIA-RDP78-03424A000800030005-7
 Declassified in Part - Sanitized Copy Approved for Release 2012/02/16 : CIA-RDP78-03424A000800030005-7
ATTAC[f1ENT toI (Work Record, Work Order No. 1 25X1
General Work Requirements
1. The antenna shall be adaptable to a frequency range of 1 IQ4C to 10
KMC and will be provided with a provision for vertical and horizontal
polarization. Broad banding need not be furnished. A connection to
a 50 ohm unbalanced line will be provided. The input connection
should be through a standard type N, 50 ohm receptacle and the feed
should be capable of being mounted in the reflector. The polarization
must be continuously rotatable from true vertical to true horizontal
since the received signal is a reflected one and polarization on
arrival is unknown. The utilization of a 36 inch spun aluminum
parabolic reflector, which will be reinforced in the back and cut
into four segments to meet the packaging requirements, is deemed
acceptable.
2. The mounting structure shall consist of a band rotable, self-
supporting pedestal mount, adjustable to 6 feet from the bottom
edge of the reflector to the floor. This mounting structure
will be a sectionalized tripod and mast assembly which will permit
coarse and fine height adjustments from 2 to 6 feet above the
floor level. It should be hand rotable in azimuth through 360
degrees, with provision for locking in any position. The assembly
will be self-supporting, without lagging or guying, but provision
for lagging should be made.
B. Packaging Requirements:
1. The assemblies should be broken into units which can be packaged
into cartons not exceeding 20 inches x 20 inches x 12 inches outside
dimensions packaged, or weigh more than 60 lbs. packaged. These cube
and weight limitations refer to any one package. Packaging provisions
for air shipment with some lightweight material such as reinforced
corrugated cardboard, plywood or fiber glass is required.
Deliverable Items Required:
packaged for air shipment.
1. One reflector pedestal assembly and onel feed assembly
2. One reproducible and two copies of all samfaeturing drawings and
parts lists.
3. Three 8 x 10 inch photographs including one shoving an assembled
view of the unit.
CON F1 DENT1AL
Declassified in Part - Sanitized Copy Approved for Release 2012/02/16: CIA-RDP78-03424A000800030005-7