APPENDIX A INSTALLATION OF ADAPTER BAR AT WIND-UP END OF A VERSAMAT PROCESSOR
Document Type:
Collection:
Document Number (FOIA) /ESDN (CREST):
CIA-RDP78B04770A002400050043-5
Release Decision:
RIFPUB
Original Classification:
K
Document Page Count:
6
Document Creation Date:
December 28, 2016
Document Release Date:
May 9, 2005
Sequence Number:
43
Case Number:
Publication Date:
July 1, 1965
Content Type:
REGULATION
File:
Attachment | Size |
---|---|
CIA-RDP78B04770A002400050043-5.pdf | 139.06 KB |
Body:
Approved For Release 2005/06/06 : CIA-RDP78B04770A0000050043-5
APPENDIX A
INSTALLATION OF ADAPTER BAR AT WIND-UP END
OF A VERSAMAT PROCESSOR
L
L
L
L
L
L
L
L
L
An adapter bar kit is furnished with each portable take-up unit. The kit contains addi-
tional parts (screws, washers, etc.) necessary for installing the adapter bar, shown in
Figure Al, on the wind-up end of any VERSAMAT processor model. Since the physical structure of
the wind-up end of the Model 11C VERSAMAT isn't the same as that of earlier models (e.g., the
11, and 11A VERSAMAT), two different procedures are listed below to cover bar installation
on all VERSAMAT processors.
To install the adapter bar on the Model 11C VERSAMAT, follow the procedure listed below.
.a. On the processor base, make four reference marks at the exact positions shown
in Figure A2.
.b. At each of these four reference marks, drill a .343 ?.001 diameter hole through
the base.
c. Jack the wind-up end of the processor about 8 inches off the floor to provide
sufficient working room for carrying out step d. below.
d. Use the screws, washers, and the two screw retention (nut) plates* provided in
the adapter bar kit to attach the Z-brackets of the adapter bar to the processor
base. Figure A2 contains a diagram showing the bar correctly installed on the
processor.
These plates are used instead of nuts so that if the bar must be raised or lowered after
installation, the screws can be loosened and retightened easily without jacking up the
processor again.
Declass Review by NGA.
Approved For Release 2005/06/06 : CIA-RDP78BO477OA002400050043-5
Approved For Release 2005/06/06 : CIA-RDP78BO477OA002400050043-5
00
1. Adapter Bar
2. Z-Bracket (Two)
3. Bushing (Two)
Top View
00
Approved: FWwj9elft se Q"Qbf (W4JOWIj78WI770A002400050043-5
3
Approved For Release 2005/06/06 : CIA-RDP78BO477OA002400050043-5
9 L F/LM W/OTH
TO PORTABLE TAKE-UP
Z-,345 tOao?~G~iA (4) HaLE5
Approved For Release 2005/06Th : CIA-RDP78BO477OA002400050043-5
Approved For Release 2005/06/06 : CIA-RDP781304770A002400050043-5
L
L
L
L
L
L-
L
L
L
L
L
NOTE
The disk cover and the four Phillips, pan-head,
self-tapping screws included in the kit are used
only when installing the bar on earlier VERSAMAT
models (e.g., the 11, or 11A VERSAMAT).
A.3 INSTALLING ADAPTER BAR ON ANY VERSAMAT RELEASED BEFORE THE MODEL 11C
To install the adapter bar on any earlier VERSAMAT processor models (e.g., the 11, or
12A VERSAMAT), the steps below should be followed:
a. Remove dryer access end panel from wind-up end of processor.
b. At the wind-up end of the processor, mark four reference points at the exact
positions shown in Figure A3.
c. Drill and tap 5/16-18UNc-2B threaded holes at these four reference points.
d. Remove the exhaust duct from the end of the processor, cover the hole with the
sheet metal disk included in the adapter bar kit, and finally install the
exhaust duct on the side of the processor. In following step d., refer to
Figure A3 and A4 which show installation diagrams and exact dimensional details.
e. Use the screws and washers provided in the adapter bar kit to attach the bar to
the wind-up end of the processor. (The two screw retention (nut) plates included
in the kit are used only when attaching the bar to the Model 11C.)
.f. Replace the dryer access end panel on the processor. If the two hexhead screws
which secure the left Z-bracket to the processor obstruct the dryer access end
panel from being replaced, make an appropriate cutout in the panel to allow for
screw clearance.
l
Approved For Release 2005/06/06 : CIA-RDP78B04770A002400050043-5
Approved For Release 2005/06/06 : CIA-RDP78BO477OA002400050043-5
j-incn aiameler nose ui i.ue eiuu ui uua yi~~cec~a
position.
If, after bar installation, the two screws which secure. the left Z-bracket to the processor interfere
with panel replacement, make appropriate cutout in dryer panel to allow for screw clearance.
WIND-UP END of PROCESSOR, DRYER END
PAM REMOVED (SHE NOTE 2)
4J I /./2d
~FJ ll~taeu~HRU AN6tE
Approved For Release 2005/06/06 : CIA-RDP78BO477OA002400050043-5
Approved For Release 2005/06/06 : CIA-RDP78B04770A002400050043-5
.2 /8 _Y;,0000 ?L7/A (4)
E6? AL. L Y 5# CCD
{ O/OL 1A
3.G25-
B ASIC'.D/A
Figure A4. Disk Cover for Opening in the Wind-Up End of Processor
~-II-~ 050
Approved For Release 2005/06/06 : CIA-RDP78B04770A002400050043-5