SCIENTIFIC ABSTRACT KUNITSKIY, R.V. - KUNNAP, E.

Document Type: 
Document Number (FOIA) /ESDN (CREST): 
CIA-RDP86-00513R000927530003-2
Release Decision: 
RIF
Original Classification: 
S
Document Page Count: 
100
Document Creation Date: 
December 30, 2016
Document Release Date: 
June 19, 2000
Sequence Number: 
3
Case Number: 
Publication Date: 
December 31, 1967
Content Type: 
SCIENTIFIC ABSTRACT
File: 
AttachmentSize
PDF icon CIA-RDP86-00513R000927530003-2.pdf2.85 MB
Body: 
8,16 S/WR(60/037/Oo6/022/022 E052/E514 Simultaneous Determination of Latitude and Longitude of a Locality from Absolute Measurements of the Altitude of Two Celestial Bodies the equations are based is not an exact formula. The latter consideration is not important when the corrections are small.. However, when the correction is of the order of a few minutes of arc, then the approximate nature of the basic differential formula may have an appreciable effect on the magnitude of the final corrections so that the calculated mean square errors are not in fact an indication of the accuracy of the final results. This is partic- ularly important in the case of altitudes in excess of 60-70 deg and when one deals with large latitudes. The present paper is concerned with the relation between the accuracy to which the approximate values of the longitude and latitude are known and the accuracy of the final values of these coordinates when they are calculated by the above method of "lines of equal altitudes". A sequence of operations is recommended which can be used by an observer to determine the geographical coordinates. It is said that when this sequence of operations is followed the calculations are considerably abbreviated and the significance of the calculated Card 3/5 87263 5/033/60/037/006/022/022 E032/E514 Simultaneous Determination of Latitude and Longitude of a Locality from Absolute Measurements of the Altitude of Tiyo Celestial Bodies errors is quite clear. The S6(jUence of operations recommended is as follows: a) a measurement is mad6 of the altitude of two celestial bodies (to the required or the possible accuracy) whose azimuths do not differ by more thall 30 deg from 90 deg or 270 degi b) the measured altitude is corrected for refraction and other systematic errors and a calculation is made of the azimuths of the two celestial bodies and the difference between their measured (corrected) and calculated altitudes (for the times of measurement and the approximnte values of the latitude and longitude of the locality); c) using the usual method (Kunitskiy, Ref.3) the point of intersection of two lines of equal altitude is found on a geographical chart (or simply on a coordinate grid) which gives a more accurate value for the position of the observeri d) using the new,more accurate, values of these coordinates, a calculation is made of the altitude and azimuths of the celestial bodies to the same degree of accuracy to which the altitudes of the celestial and which are to bodies were measured; e) the corrections tA Card 4/5 S/033/60/037/oo6/022/022 E032/E514 Simultaneous Determination of Latitude and Longitude of a Locality, from Absolute Measurements of the Altitude of Two Celestial Bodies be added to the values of latitude and longittide obtained in (c). are then calculated from equations of the form sin A a hl sin A 1h cos A h - cos A A 11 A(P 2 1L 2 ; AX = 1 2 2 1 sin(AI A2) cos sin (A 1 -A2 (11) where h is the altitude and A is defined by Ah = - cos AAy - cos y sin AAX. (9) This sequence of operations can be used when the longitude and latitude of the observer is known to an accuracy of 1-2 deg. The accuracy of the final result depends only on the accuracy to which the altitudes of the celestial bodies were measured. ASSOCIATIONa Moskovskiy gos. pedagogicheskiy institut imeni V.I. Lenina (Moscow State Pedagogic Institute imeni. V. I. Lenin) SUBMITTED: May 12, 196o Card 515 ASTAPOVICII,I.S.; RAETOX UtUVSllTF,1-7,V.A.; BUGOSLkITSKAYA, NI.Ya. [deceased] VASILIMpO.B.1 DUJj;~,OVO"KIY,K.K.idcccased]; ZARIUi-OIT,G.P.; ZDI%Dl,I.T.; KUi'OCHI:I',- Mlimov,Ye.L.; KIJLIK0VSKIY,P.G.; K' L . OHLOv'S.V.[deceased]; POPOV,P.I;; PUSHKOV, N.V.i RYBAKOV, A.I.; RYABOV,Yu.A.; SYTINSKAYA, NJ%; TSESEVICH, V.P.; SIIGIIIGUlSI',B.M.; VORONITSOV-VEL IYAMID' OV,B.A. red.; F(Jj'W;Ai0!A,G.k., red.; MUMMA, V.1%, telchn. red. [Astronomical calender; permanent part] Astronoricheskii kalendarl; postoiannaia chast'. Izd.5., polnostliu perer. Otv. red. P.I.Bakulin. Red.kol.V.A.Bronshten i dr. Moskva, Gos.izd-vo fiziho-mater..lit-ry, 1962. 771 p. (M~- 15-4) (Astronomy-Yearbooks) KTJNITSKlY, R.V. (Moskva) For the elimination of computational illiteracy. Mat. v shkole no.3:50-52 MY-Je 162. (M]IJbI 15:7) (Mathematios-Study and teaching) ?T!qj,1;KIYj 11 4-p ,,Y yof. Astronomy In atheistic propaganda. Zen, i veal. I no.1j4).47 Ja-F 165. (WRA 18s7) _z=-ugly, V.. ~~ardil -poll-,ovnik: ZASO&TMA-V, I.. gvardii polkovnik. , Directing mortar fire at night. Voon- voct. 35 no.8:60-64 Ag 155. (14ortar3 (Ordnance)) (MIRA 11:3) KUNITSKIY., V.N.; GAUZSHTEYN, D.M. Methods of censusing fleas in the entrances of burrows -)f the greater gerbil (Rhombomys opimus Licht.) Zool. zhur. 42 no.11:1743-1745 163. (MIRA 17:2) 1. Central Asiatic Research Anti-Plague Institute, Alma-Ata. KUNITSKIY ... V.H.; KUMISKAYA, H.T. - * Now species of flea, Ceratophyllus mikulini i3p. nov., from Transcaucasia. Trudy Nauch.-iosi. protivochiun. inot. Kav. i Zakav. no.5:203-205 161. (MIRA 17:1) KUNITSKIY, V. N. Habitat conditions of fleas parasitic on gerbils In the southwestern part of the Azerbaijan S. S. R. Zool. zhur. 40 no.6:8 8 8 8 Je 161. ~MIRA 14:6) 1. Anti-Plague Research Institute of the Caucasus and Transcaucasia Stavropol-Regional. (AzerbaiJan-Fleas) (Parasites--Gerbils) GAUZSHTEYN, D.M.; KUNIMMY, VJI,, Species of fleas on birds of the southern BaIkhash Lake region as related to the possible participation of Urds in spreading the plague infection. Zool. zhur. 43 no.10:14?3-2,1479 164. (MIRA 17s!2', 1. Central Asian Research Anti-Plagus institute (Alma-.Ata~,. KONITSKIY, V. Kunitskiy, V. Ps "To guarantee further development of the peat industry," In symposium; Torf v nar. khoz-ve Belorus. SSR, Minsk, 1948, p. 25-37 SO: U-3566, 15 March 53, (Letopis 'Zhurnal Inykh Statey, No. 13, 1949) Ya Yc . I, ,.. -i ~ ~, 1, -1 1 , - . "So7riet Amxiratus for Injectuinr, Under Preaeure, Ana,-tilieti-c Into T-i"OlUeSill I'c).10, pp 64-65, 1951 Trans latim--~ -.,*-',l592L, 25 1-61) 52 USSR/Cultivated Plants - Grains. M. -As jo~~ : Ref Zhur - Biol., iio 4, 1958, 15529 Author : N.V. Turbin, L.I. Lovotskaya,. Ye-A. Kunitskiy Inst Title The Principal Results of the 1955 Experiments on the Study of Corn Varieties,, Strains and Hybrids as Initial Selection Stock. (Glavneyshiye rezulltaty opytov 1955 g. po izucheniyu sortov.. liniy i albridov kukuruzy kak iskhodnoGo materia- la dlya selektsii). Orig Pub : V sb.: Kukuruza v BSSR, Minsk,, AN BSSR, 1957, 24-59- Abstract : This study which was conducted at the Bielorussian State University in 1955 was dedicated to the problem of ob- taining hybrid corn forms exhibiting heterosis in the Bielorussian SSR. Intervarictal, variety strain, inter- strain, complex double and triple hybrids were studied, as well as the hybrid population of corn. Card 1/2 USSR/Cultivated Plants Grainsa M. Abs Jour Ref Zhur Bioli, No 4, 19581 15529 Many of these significantly exceoded the parental forms in yielding capucity and other economically important characteriatica, howeverp not all proved advantaLreous in cob yield as compared to the better varieties. In cob yield (in the presence of harvesting m-isture) and green stuff) the complex hybrids and hybrid popula- tion took first place, the sinple interstrain hybrift second, varietal strains took third) and the intervaria- tals last place. Card 2/ 2 U.-DR/General Biolo,-y. Genetics B .s.' hbs Jour Ref Biol., No 13, 1~'58, 5?193 !.uthor Turbin 1.. V.,,Lobotskaya. I.. I., Ye. A. Inst -Deloruscian University Title the 1955-105S -x,.)eri~:,nent:, for Main qesults of I j the ',tudy of Varieties, t IAnes, and Hybrids of 14aize ast ~'he Initial Porm for the ',election of Hybrid ;"-...ize Under Conditions of Belorussian SSR Ori~3 -Aib Pub. Uch. zap. Belorussk. un-t, l,,5/, v7P- 3?, 255-32? Abstr,c'- On t~ie basis of ',)reliminary studies the follow- 4ng initial forms are recacwended as Vie best for the selection of corn in Belorussia- e,-..rly ripening and medium early-NichkassIcaya, Niel- kaya k1lulinshatya, Sew)ryanka, Belaya Pireneys- kaya, Voronezhskaya 76; ?-iedium ri-oeninF-,--' C.-.rd 3.12 33 U JSR/Gerieral Biology. Gen~-.,tics Abs Jour Ref 7,aur-T'i0 1-To 13, 195~, 573-93 Abstract 7q.ndorfskaya .nd Zubovidnaya ?35, Of those '1e "intslzht line", "nbovi'n-ty-. 2112, .!cd 'roi U j T,94 "Ind V,-95 - re reco -. ended. Good 'ualit-, I-o- cal nterv,ricty hybrids ~1,m~ Ticc7A o7)t--,in,,,d; a 'I iltv-.iLskay.-i+l,'es-tTi,,iyfi )olessky~ 1, 1,evorodalco- tsl~aya+Pii;:ture of )ollens of Abkhaz varieties. In their yield they :-.re sup.2rior to `.ntervari- ety !-tybriCLs. An ev~luatuinn of"intsuk' t-lines" w-,.s made on t e basic, of t.-!eir hvbrids, .,ith avai- lable varieties of maize. The oDinion 'nas bec~n exnressed that separ--,te tests of a line malce it Possible to hope -b'hat on their base hi.-."hly -oro- ductive interlineal hybrid.s may be obtained in the future. CArd 2/2 USSR/Cultivnterl Plants - Fadder. M. Abe Jour ; Bef Zhur - Biol., No 4, 1958; 15702 Author : Z.A. Kunitakiy Inst Title : The Corn SOwin-f' -,Ire-r`i~ds in Minskiy Rayon. (0 srokakh poseva kukuruzy v usloviyakh MinskogD rayona). Orig Pab : V sb.: Kukuruza v WM, Minsk, AN BSSRI 1957, 268-2-(3 Abstract : Experiments were conducted at the biological station of the Dielorussian University in 1954-1955 on the de- termination of the best corn sowing periods for Bielo- russia both for -xeen fodder and for ripe staCes. In 1954 the experiments were made solely with non-vari- etal corn., in 1955 with the comon one, North Dakotan and Sterling. The sowing tines were in 10, 15, 25 and 30 Mayo The largest corn yield in GTeen stuff and cobs was gotten with medium early sowing on 15-20 May. Card 1/2 USSR/Culti'latc" Pll'nts - FAdk:r. Abs Jour : Ref Zhur - Diol.) ITO 4; 1956, 15'102 It was only with these sowingr periodo that cobs in the iraxy and even con,13lotely ripe staGea could be obtained. Card 2/2 I/) UMM3MUU, G.X., MaEaROVA, A.N., gl.=LM3, V.V,o SMWAO KX Nwv mma=r for the yroftatian cc tb syntboric flimm dod"Llaktan. Beport to be sawittod for the IM Conforw"s cn h1& m*Uculsr v*l&t oacpomds aentod to somwes Za)mp 3-7 APII 62 KWITSYA, H.O., RLDZIYNVSIKIY, V.I. Geomorphological subdivisions of the Goryn River valley. Dop. AN URSR no-5: 488-493 155. (14IRA 9:3) I.,Institut geologichnikh nauk All URSR. rredstaviv diysniy chlen AN URSR V.G. Bondarchuk. (Goryn Yalley--Geology, Structural) KUNITSYN, A. PA 16/49T36 Aug 40 Bushings Rotors "Replacement of Bronze-Graphite Bushings and Die- n tributor Rotors, A. Kunitsyn, i p "Avtomobil'" No 8 Refers to articles on this subject publishe& in "Avtonobill" fic, 8, 1947. Describes own experience using various materials for parts named. FM 16/4nz 6 oil 4fill j3s .3, I U. bill - Ia lilt 114 .15 's'ly! I 10-58-2-26/30 The 4th Conference of Young Scientists of the Institute of (~vography of the USSR Academy of Sciences 1957 (Ixv Ak nsuk~SSR ser jaug 1958 No-2, P-151-53, Gorbunova, M.N.) formation of the reliel of the kdb:i~nY tundras; L.F. Kunitsyn * Fe~_ on characteristic features of perennial frost in t north- west Siberian lowlands; N.S. Blagovolin on the morphology of karat occurences in the Aldan plateau; A.V. Yermakov on erosional waters in the Central Caucasus; A.A. Mints and B.S. Khorev on quostions concerning economic-geographical typology of socialist cities exemplified by central industrial regions of the European part of the USSR; V.S. Mikheyeva on the typology of soil organization in the k.)lkhozes of thc.Trans-Oka region., Moscow Oblast'; B.S. Khorev on the industrial utilization of forests in connection with the construction of the Bratsk hydro- power plant and the creation of an inundation zone; I.A.P. Khis- matov-on the utilization of mineral resource.9 in northern Bashkiriya; K.N. Chernozhukov on t4& development of agricultural prrjduction and the utilization of trbpic resources in South China; Ya..M. Berger on the industrialization of the Sinltszyan- UygmrdxQaAutonomv,q Q'"Ipqti (China); Yu.L. Pivovarov on tho to*rmation of the0strava industrial center (Czechoslovakia); Card 2/3 A.A. Zasukhin on basic structural and geographical shifts in KUNITSMI, L. F., Candidate Geogr Sci (diss) -- "Analysis of the natural condi- tiom in north5rn Transuralia for selecting the direction of the Tiral-pechora railroad line". MOscawj, 1959- 15 pp (Acad Sci USEZ~, IrLqt of Geogr), 110 copies (KL, No 23, 1959, 162) I The Sixth arferezce ol 5cie-tific 77orkero of the a-titut Geo:mfli Lr of Gto- Sraphy Ar, U_'aR) 1z"-.tiTa Ik-e=ii nauk 3733, Zer~,a kaya, 1959,.*Tr 4. ;p 152-154 (Z?3 3 17,=: SLT-h ~~on-fcr~zce of To-j=Z , The Awticle covers V~ he 1=3t1-ua or Gec7rap!Z7 t Sol satiric 7orLero o- &S MDR b.1ch took. place In zld-t~armh, 19~9- 35 reports seem read by the follovlln~; scientific ~-.r- kers. 1.Z.Sl%Xnh rr;orted on -Zo=o genetic ties In the ~Istrib-jtjon of lktnos~,.Iric prec-1;1-a- tiom 70t, r_- C.14. on, otrut. 'Tq 3no.- 'oe" .kutarctlc rezionj -rokT on - ITM7 tion bmt=eem =1c r Card Lk, =4 the lste3t in the - -"rr1nr-Uri1 Lrea. a e-all-ated tho a to :&Poratiom accore. bal=ce =cth~,d , on the A.-Irleaz ccatineztg Z~Zg~~- a 1111 c- evaporatict 7rot~lena In the :;~J_F of ported _ .. N i : f -_T nPact Of svl3r ra!IA zn A7o- d _ i:LZ: its Moltiz:; 1= the Trsn=--,oirzL rericni '_ 'r, C,-oka on stow rmitiati--c. tear he 77eatr.-Tr stam-lozi lectred o= azo7 cc~niitio=a J_- -he Ito taizm of Central Caucasus; 'T.71. Crlov reported on, his 22" to Imassurs, mzc~. carried by wLzadls. w!iereby G=,e-flLko3 a-._ reecrije-~ by a photoelectric lericep -W-U, and i-ja m r a 040 on the he=, balance ~Nser - P - a hey C, I ratio a t at tt:e Z1 i M -orckva sciettilf- Station near ':oacc7j - - I Y 0:3 spri=; _ Water dlzcLame zmZl B~ ,, nva"ie., Card 2/5 Dreyer Lnd !.N.Ztetheasl_-~-a 1~ct,;red on he, to C&lcuLate ~iL. B;7r--a,; ater dischar,~~ in the Ter-isey and Lena rivers accordim- to the Iteth0d Of c'3 ,ev a red on. sea ler~la _ ce.,t~ric- =1 g UZ ~ZLC -D--1 sea uz m~; ac 7 on 'he Z.L~ lereiz to the j Pre asion d-,Lrim,, 1,549-1158; - I "'s- reported tm i t the rivero am., lak.'m - a~ e2.t Z~~- * l , i,i _ ' ; i- ~ i i = t " discusoe, =s a rt le e r 7 iocena or of -;_~e r.- barijej 1 - 1 elucidatel 02 lefts de;:~sjtz in -he ent-ni 3raz or the ;Limj lectured! c!" 'Torre.t-Llk, --he-onew tication of Torrents it Caz,~'FiT he :;Oobat,~IIC Surrer ~: -:,0 :;e1tr5l 1-1; 0= th., or the Card .515 Zrml rood-=: -otep; a a:mea into zi-.Zle relief -~-,eag ji, A The 31-th Conferance of TourZ -titific 7orlter.1 0r I=titut Geasmai za U :3-a (1~='Stltota of '-'raphy AZ USZ:2) alnel ho- tillt hal On the ~':Rvsq2ft lt~. IrMh' rl~ir near F'vlol&r mrigl- Emv* a short =1 g6oarayh1cal aurva;" on the Tr=s-_1n_'_' L~ I.& --44_ Veazher reported am !:_~r work exerience Im :.-a =tt- acap of morphogenotir, ground male photoCraph7 In the Jh_7GtSknzx 1=2. I A* Ti,nofeyev discussed relief crizLn in the 2:7 t2ze Part of the A=tLr am-% Z97a rivers areas 7.F. hm-or 0ozWar*d norpholoelcal and =vrpho=etr.4C =1 -DIG measure -all coefficiontal OX. "J-0 C-re a ... V ~_%o part of the Talrutakara ~M=j To.:% ~1%1-".Iq "ported on the deyelop=eat of the &reat -11.1 _ 0 - ~44vcu"*d data on the ;Uztrit-u- tic =7 .1barares in t!:,e fic~Anz ec~nor'y of the Ivakiyakir ~atsioznl'm.77 ckrua (::-en1,_'! -,Atiomal C.M. rem)& 7 r a- n,- -Ov re~or%~! on t%e at.; I. !,or k~~ -7 In -3 Ct", N. ust- the Ar h,n;el k3j mv:' and Gor'kovatij ekoroziaheakiy rjon (Gar'kj:r 3conomic District) respectivelyl I I ---- lectured am the tr&its, popu ationt and econam7 of the Lind Test Germarq. The conference wan %1t,, &t-enjej 414renentativen of the toakoyskly E;ova;i&zn-vemW univervitet Woscov State Univer3ity) :a--"".. institut proemozov (central rzz-itu:e r Inatitut =erzlotoredemiya Ll; '1-!*, (In t :?l ~t; or ne~L_ rroat Research 13 1=53), and other oreazi-atizza. The following senior workers of the Institute vf Gooers. Eby.AS USSIR took part 1z the dlecusoiamzo -F. t 4.1 taov, B.L. D-zer.'zoy.wakly, L.D. Dolzud-~. A.C. Doakach, N.B. Duzitrashkol :1.1. Wv"ict,, 5-7. :~~- axanteave V.?. gribn;7~, B.A. 7odorovich, aj-- ~,mvrs. Card 5/5 J4, NUNETSYN L.F L~ Physicogeographical regionalization of Kamchatka. Biul.MDIP.Otd.geol. 38 no.2tl64 Mr-Ap 163. (MIRA 1615) (Kamchitka-Physical geography) - KUNIITSYN, L.F.; NIKOLISKAYA, V.V. First voluiw of the Kamchatka Branch of the Geographical Society. Izv. AN SSSR. Ser. geog. n0.5-140-141 S-0 163. (WRA 16:10) KUNITSYN L.F. -- - -.-- Problems of the physical geography of the Urals, Izv. AN SSSR. Ser. geog. no.5:150-151 S-0 163. (MIRA 16:10) let's organize brek manufacturing on each collective farm. Sell. stroi. 11 Li.e.12J no.1:20-21 Ja 157- (MLRA 10:3) 1. Glavnyv inhener Krasnodarskogo krayevogo uprav3eni" po stroitell- stvu V kolkhosakh. (Brick-making) KUHITSYN Surface ensilage of foods. Sell. stroi. 12 no.7:19 TI 157. (KRA 10:8) 1. Glavnyy Whoner Krasnodarokogo krayevogo upravle'niya po stroitellstvy v kolkhozakh. (SiIQ KUNITSYN, IT.; ZARINA, At Collective farms of Kuban sill make one hundred million bricks. Sell. stroi. 13 no.6:10 is 158. (min 11:6) l.GlavVy inzhener Krasnodar kop krayevogo upravleni7a po stroitell- etvu v kolkhozakh (for Kunit:yn). Z.Starshiy ekonomist Kiasnodarskogo krayovogo upravleniya po stroitel'stvu v kolkhozakh (for Zarina). (Kuban-Bricka-ld ng) bin 1131 30*4 41 Jut) 4MAS'Co I-- & L I-L-A-1-1-1 -1-1 00 4 ', r- 77"Y 1- !. -D ~, -~~ t4'0t~j V ---- fW16SIS A P000161al wbee - - --- a 1 I -o T 1 ~ w w t omb" Dobob in 11101111U. F. Shanovskiy 1-60 go- and N. Kul gVtL (SUJ, I(W, -NO. 8, 23-25). (In Busailin). -l t4nnc (TeTWN o the scarfin of blooms wi a ox A et b '00 6 y- ento urner n c g ) n I 'IeveloptA at the SibcTia blet&U i Institute'are describoil and -00 0 the nwilts art, Vomiltaw with It obtainable by ltneumatie ' 609 : V Olippitig, 1 he lataxio of the burner has a coutral op;ning for the ~60 oxygen cutting strown and a number of conventrically-ptaml small olleninp for the acetylene Raw. The various nummcal results 4r , itulicate that ittio4warfing in about five or six times as efficient as x ~~ chipping and (-all remove such ftwioux defects " tvara anti foldn. Tht, rumoval in Also much more thorough, Tito danger of " digging " i h l h b w n en us ng t e urner twelessly in mentioned. Gaii-acarfing re can be- cheaper than the mechanical method, wA it is possible that a ; the gas consumption may be reduced stW further by appropriate go- choice of nozzles. Ile surface produced is satisfactory. roe 00 q ago Mali t; cis 0 S a . S L AAlITALLURMAL L171RAYURE CLAiSSFICAITION Z- 0 0 4,0,34!) .,-L V - T- i sailing-( 411111 C4i %V &it ' TA KA . F 21 U It AT 00 it i 04 a I s 0, 0 1w 0 is U 0 e 0 * 0 e 0, 0 0 * 0 0 0 0 1A A I I rw 0 V I w of i ii a 0 a 0 0 0 k 3 S V USRAaEoeerlng Sep 48 Welding, Autogenous Welding - Methods , "Use of Coke evas in Place of Ac6-,,ylene," N. M. Kanitsyn, Engr, Siberian Metallurgical Inst, 3-41 PP "Stall" No In Coke gaa can be used instead of acetylene for auto- genous welding. Discusses theory of combustion and design of nozzle. 6/49T13 V /\j AV/ A 41T "'~Jo V Ic- KUNITSYN, IIS.;L~VS S, M.M., redaktor; GOLYATKINA, A.G., redaktor; VA. V.V., tekhaicheskiv redaktor [Gas flame surface hardening of rolling mill rollers] Gazoplamen- naia poverkhnostnaia zakalka prokatnykh valkov. Moskva, Goo. nauchno- takhn. izd-vo lit-r7 po chernot i tavetnol metallurgii, 1953. 70 P, [Microfilm] (MLRA 7:10) (Rolling mill machinery) (Metals-Hardening) SOV/137-59-1-814 Translation from: Referativnyy zhurnal, Metallurgiya, 1959, Nr 1, p I 10 (USSR) AUTHORS- Kunitsyn, N. M -, Shamovskiy, E. Kh., Yakovlev, 1. M -, Soroko, L N. TITLE: The Design of a Wide-path Cutting Blowpipe for Flarne Cleaning of Metal (Proycktirovaniye shirokozakhvatnogo rezaka dlya ognevoy zachistki metalla) PERIODICAL: Izv. vyssh. uchebn. zavedeniy, Chernaya metallurgiya, 1958, Nr 3, pp 154- 160 ABSTRACT: The authors describe the design of a slot-type head for a coke-oxygen operated cutting blowpipe for surface flarne planing capable of pro- ducing a groove 100- 150 mm wide. The ratio of the groove width to the width of the exit slot on the head amounts to 2-3. At a groove depth of 4-5 mm, the rate of Cutting amounts to 6 m/min. The rate of cutting metal preheated to a temperature of 900- 1000C [sic!) increases to 20-21 m/min, the heating time being reduced from 8- 12 to 2-4 seconds. The stability of cut and the cross section of the groove are functions of the geometry of the nozzle and of the nature and the dimensions of the hot spot. The shape of cone-and-slot type Card 1/2 nozzles is most efficient in preventing bifurcation of the groove. SOV/1 37- 59-1-814 The Design of a Wide-?ath Cuttin.- Blowpi-pe for Flarne Cleanin.r, of Metal Smooth transition from the throat to the slot of the blowpipe is ail essential con- sideration in the design of the nozzle. G. K. Card 2/2 s/148/6o/ooo/oio/oi6/o1;,1 A161/A03O AUTHORS: Nazarov, I.S.; Korochkin, Ye.T.; Kunitsyn, N.M. TITLE: Autogenous Steel Furnace PERIODICALt Izvestiya vysshikh uchabnykh zavedeniy. Chernaya metallurglya, 1960, No. 10, pp. 157 - 162 TEXT: The Siberian Metallurgical Institute has developed a new type of steel furnace, based on the same principle as autogenous cutting. The small, 0.3 ton capacity, experimental furnace has been tested at the Kuznetskiy metallurgi- cheskly kombinat (Kuznetsk Metallurgical Combine). 2 It is shown in the cross sec- tion drawing (Fig. 1). The major data are: 0.5 m bottom; 0.16 m deep bath; charging through removable top; combustion products were let out through two ducts straight in-to the foundry air, and gas through ports in the roof; 8 bu of design shown in Figure 2 were inetalled 50 mm above the metal surface in spe- cial magnesite blocks and stuck 10 - 12 mm out into the furnace to get the flame close to metal. The fuel was coke gas with oxygen; the burners were cooled with water. Both types of the tried injection burners proved unsatifactory (the flame was pulled in at a slight pressure increase above 1.5 atm above normal atmospheric Card 1/5 Autogenous Steel Furnace 8/148/60/000/010/016/018 A161/Ao3o pressure). The experiment conditions were unfavorable - the furnace only worked periodically when oxygen was available, and it could not be normally preheated, heat losses in the small furnace were high, and the burners did not work well, but the metal melted rapidly and could be brought to 1,6500C for tapping without any difficulty. The mechanical propertie5 of the metal were close the convention- al open-hearth steel, and hydrogen content did not exceed the usual. The conclu- sion was made that the autogenous melting principle is feasible, and metal can bo melted fast'and heated to a higher temperature than is possible in an open-hearth furnace. The furnace is extraordinarily simple, may be easily automated, and steel of any composition may be melted by addition of alloy elements to the end of heat process. Experiments with lax1ger furnace are necessary. The principle may be applied for speeding up the heat in existing open-hearth and electric fur- nages. There are 2 figures. ASSOCIATIONs Sibirskiy metallurgichaskiy institut (Siberian Metallurgical Insti- tute) SUBMITTED; May 13, 1960 Card 2/5 Autogenous Steel Furnace Figure I Pajpry.v 9B CO ?NO r-A Izi S/148/60/000/010/016/018 A161,,Ao3o Card 3/5 Autogenous Steel Purnace Figure 1 (continued) s/148/6o/ooq/o1q/oi6/oi8 A16iAw Autogenous Steel Furnace a Card 5/5 S/148/6o/ooo/oio/oi6/oi8 A16i/Ao3o XMITSY-N, P.V., nauchnyy sotrudnik. Method of determining the water absorption of building stones. Stroi.prom. 31 no-10:31-32 0 '53. , NIRA 6:11) (Building stones) KUNITSYN, S.A. The K-471B single-crank double-action press with 100/63-ton capacity. Biul. tekh.-ekon. inform. " t0-3:12-13 16o. Wa- 13:6) (Power presses) AUTHOR: ISAYEV,A.I., KUNITSYN,S.I. PA - 3613 TITLE: Investigation of twe-m-y-nama-ce of the Cutting Process for the Gearing of Bevel Gears by Means of Cutting Heads. (Issledovanie dinamiki protBessa rezaniya pri narazanii konicheskikh koles krugovymi zublyami, Russian) PERIODICAL: Stanki i Instrument, 1957, Vol 28, Nr 6, pp 12 - 15 (U.S.S.R.) ABSTRACT: This investigation is of direct practical importance for a rational selection of the cutting values, the construction of cutting heads, calculation of the strength of the components of the kinematic lines of machines, the selection of suitable driving motors, etc. Besides, it is possible, according to the law for the variations of cutting force components, to calculate working accuracy in consideration of the rigidity of the elastic tachnologi*cal systems machine-workpiece-to6l. As shown by experiments carried out, the diameter of outtings dif- fers; it depends on the position of the cutter in the cavity of the gear to be worked. Cutting widths of the exterior and interior stail cutter are not equal, which means that they are also subject- ed to different stresses. As may be seen from illustration 8, the maximum stress acting upon the outer steel cutters is up to 3 times as great as that of the inner cutter, which means that it will also be subjected to greater wear. The different stress acting upon Card 1/2 Pk - 3613 Investigation of the Dynamics of the Cutting Process for the Gearing of Bevel Gears by Means of Cutting Heads. individual steel outters.exercises considerable influence upon the accuracy and neatness with which surfaces are worked. Detailed calculations follow. (12 illustrations and I table) ASSOCIATION: Not given PRESENTED BY.- SUBMUTTED: AVAILABLE: Library of Congress Card 2/2 'Tr - j, KULIITSYN, $. I., Cand Tech Sci -- (diss) of the effect of cutting And hardneso 4f of :al~;,machlne 0f-04 the Ito Tcto= 4~ bevel wheels with circular g=ars." Mos, 1953. 13 PP. (Min lilgher~d USSR, Mos Aviation Tde~;~ Inst), 100 copies. (KLP9-MJ8, 118) - 75 - AUTHOR: None given SOV/122-58-6-36/37 TITLE: Authors' Summaries of Dissertations (Avtoreferaty dissertatsiy) PERIODICAL: Vestnik I..ashinostroyeniya, 19582 Nr 6, p 8? (USSR) ABSTRACT: V.A. Antonov - Investigation of the Centrifugal Cleaning of Oil for a High-speed Diesel Engine (Issledovaniye tser-ttro- bezhnoy ochistki mablana bystrokhodnom dizellnom dviE~atele). The suriunary was submitted to zhe Saratovskiy sel'skokhoz- yaystmemyy , institut (Saratov Agricultural Institute): the rusults of an experimental investigation of the effect of centrifugal cleaninE and filtration of oil and of the effect of the additives AzNII-4 and TsIATIM-339 on the wear of a stationary hi&-spee6 engine and on the aLeinE of the oil are reported. ArisinG from the investiL--,-,.-tio-n carried out, it is concluded that centrifugal filterinr.' uf oil in the lubrication system re(luces the wear of the 2Ch-10.5/13-3s engine more than two-fold. Kh.-Kh. Kendzhayev - The Effec-b"'of the Blunting and Idear of a Grinding Wheel on Output and Precision in Cylindrical Grinding (Vliyaniye zatupleniya i iznosa shlifoval'ri,-);,,o kruga na proizvoditellnost' i tochnost' obrabotki Dri kruElon shlifovanii). The suiutiary was submitted to the Moskovskiy Card -1/Z ~, SOV/122-58-6-36/-? Authors' Summaries of Dissertations stankoinstru.mentallnyy Institut (Moscow Machine Tool and Cutting Tool Institute) ime-ni Stalin : the quantitative relations between the wear and blunting of a grinding wheel on the one hand and several factors affecting the grinding process on the other hand have been established as a result of tests carried out. The relations between the wear and blunting and the output and precision of grinding have also been found. A.S. Yablonskiy, N.S. - Problems of Design and 17anufacture of Ron-circular Gear Wheels (Voprosy pro ektirovaniya. i proizvodstva nekruglykh zubchatykh koles5. The sum.-ary -aas submitted to the Leningradskiy politekhnicheskiy institut (Leningrad Polytechnical Institute): the design of a modi- fied gear hobbing machine for the cutting of non-circular gear wheels with closed centroids is described. A fixture for machining such wheels with the help of an external master is shown. A new variant of a modification scheme for a stan- dard gear hobbing machine is proposed. Gear hobbing inachines so modified can be used to cut both circular and non- circular gear wheels. Card 2/6 Authors' Summaries of Dissertations SOV/122-58-6-36/3? M.N. Pilipenko - Investigation of the Operation of Roller-type Brakes, Backstops and Other Free-wheeling Mechanisms (Issleaovaniye raboty rolikovykh tuormozov, rolikovykh ostanovov i nekotorykh drugikh mekhani.zmov svobodnogo khoda). The summary was submitted to the Leningradskiy politekhni- cheskiy institut ~Leningrad Polltechnical Institute) imeni ILI. Kal-inina: based on theoretical and experimental studies of free-wheel roller mechanisms, the conditions of static and dynamic wedging and disengagement of the rollers are established. The limits of reli'able functioning of these mechanismsare given for the cases when the driving element is the profiled sleeve or the external race. Based on these studies, a new roller mechanism has been developed, free from the drawbacks of existing designs. A procedure for designing the new mechanism is evolved. P.I.-Eugitsyn - Investigation of the Effect of the Cutting F-orces and- the Machine Tool Stiffness on the Machining Accuracy of Bevel Gears with Circular Teeth (Issledovaniye vliyaniya. sil rezaniya i zhestkosti stanka na tochnost' obrabotki konicheskikh kole5 s krugovym zubom). The suminary was submitted to the Moskovskiy aviatsionnyy tekhnologi- cheskiy institut (Moscow Institilte.of Aviation Teclinolor,): Gard3I the dynamics of cutting bevel Mare with circular teeth of modules up to 2.5 mm and the stiffness of the machine-workpiece-cutting tool system are analysed in the dissertation. The effect of the elastic deformation of the machine tool components on the accuracy of gear cutting is established. The machining finish of the tooth profile depending on the cutting condidtions is examined. The studies carried out can be used in designing machines for cutting emu pitch spiral bevel gears and for predicting the machinining accuracy and the finish obtained NrYXKKKMXXXX on Me tooth flanks. card 4/4 ISAYIVq A*I&, doktor tekhn. nauk: KMTSYN, S.I., inzh. Investi .gating the effect of mchine-tool rigidity on the precision of mchining round-toothed bevel gear. rest. mash. 38 no.T:73~-77 Ja 158. (MIRA 111:1) (Gear cutting) fv I /V S. IL rMU I Bow WwrWrax am/" Allt.40MAVY "kinaZagIch-SkI7 inotitut logl#40M yq VMt$o1sqT vpokc7r*Iovo-UtoI*w7 ebrsbotkl Stt&Uuv n"Alrd i I Analysis vf %i6-Vr*&btttVLt7 YAW-Atiq Y-~F O's-VII 1959. 130 (801661 Itst tradY, M. 38) 3,6W coviss PrIht44- ft-A-IR4 Apwjj Hipiptorotro Tpo'bego dbrovoTonlys BOX. 3:1. TooM, Doctor of TwImIcal 0 towo*, ptarefoorl 9d. Zd. (Title M A (1"180 back I I Rginseri M. f Zli.blg &a-, ?J. Harotmi Toeb. PA.! N.A. PakUllural Monaging Rd.s A.S. fAymovskows. ruKp=l Tills avaloott" of aftialso to faterlod for dostpors wd engineers to the field of nochino-tool o1alpseat &M mehialeal machining. It my also be useW to vorlore at sateatifle research hatitites arA aspirants. CMEPAMI This Causation of artistes 6sals vith Prouss, ~rj.j., I. Mt- proftctivity metal-vattirg Processes. bouts to given)So plating uporstiou for parts zMe from eftstractic"I alloys. . Vischtelog: regime and potbods of 1"rali" mchining Overatia" an vvastot*14 so vervatialties an mationed. Reforow" rollas, seab artlele. .=~,[Csrftdate at TeaNdcal Selowes). FrOwneacy mA Amplitade of -Matra III - ey Vitratlow of Ungle-polat Toole barlid fttting of a, Steals With Ywr PhsahLasb1lity Ty csdiuts at Technical Below" Kyallm 1 1. Irr"t of tbs pysadca 11--m- - Rigidity of the Tval on the Accaracy In MUM OpIrsl Moval Gears 87 at A.T. [CabUdate of Technical Selooe"). Thmo-eampamat Dywooseeter VR901aft Traaaames" rar ATAIIAMIXt Ubrary of OODSreso Cut 3/) KMTSYN, S.I.; Tll'.-,llKOVV S.-T. Fffl~,J-enl, gawTetry of cutt'Anp, twl: for maclAnine mlinpunc-v, 2 g 1, ~X. 0 Lee-IT. Sttin. i -1yinLr. 35 0 164. (141M 17.12) EMIITSYN, V. D. k Syndro'me of hydrauIte trau of lower segment of the spinal cord. Vopr. neirokhir. 15 no. 3:50-55 May-June 1951. (CUML 21:3) 1, Penza. USSR / Human and Animal-Physiology. The Nervous System. T Abs Jour: Ref Zhur-81ol,, No 9, 1958, 41683. Author Kunitsyn, V. D. Inst te-n-z-a- a -"MT r 7 '~s p I t a I . Title Hydraulic Factors in Trauma of the Central Nervous System. Orig Pub: Sb. nauche robot vrachey Penzensk. obl. bolnitsy. 1957, No Z, 26-35. Abstritct: The sudden displacement of the cranium In space appears to represent the basic pathogenic Instant of disturbances observed in brain injuries. In this, the cranium, representing an integral hard system,transmlts the impact to the brain. A hy- Card 1/2 USSR / Human and Animal Physiology. The Nervous System. T Abs Jour: Ref Zhur-Biol., No 9., 195811 41683. Abstract: draulic Impact results In the ventricles of the brain, Injuring the adjacent structures, The resulting Increase in intracranial pressure leads to distortion of the circulation in the whole vascular system of the brain. The hydraulic shock also Injures the nervous apparatus of the cerebral vessels., which causes denervation of the vessels. The authors propose the substitution of the termi- nology "cerebral concussion" by "syndrome of the hydraulic cerebral trauma" reflecting the patho- genic Instant of the Illness, - M. N. Fishman, Card 2/2 110 USSWFarm Animals. Smal I Horned Stock - Q Abs Jour: Ref Zhur-13iol., No 4, 1958, 16818. Author Kunitsyn V. I. inst Title The Influence of Different Types of thA Semen of Rams on the Quality of the Progeny (Vliyaniye razlichnykh tipov semeni baranov na kachestvo potomstva) Orig Pub: Sb- nauchno-issled. rabot stud. Stavropol'sk. s. -kh. in-t, 1956, vyp. 4, 76-79. Abstract: In the experience of artificial insemination with a nixed semen of two raw of the .8tavropol' breed, bred under different conditions, the per- centage of fertilization was 99.6 and 97.6 as ag- Card 1/2 USSR/Farm Animals. Sms1l Homed Stock. Abs Jour: Ref Zhur-Biol., No 4, 1958, 16818. ainst 93.8 and 95.1 in insemination by unmixed semen; the number of lambs per 100 dams amounted to 162.7 and 144.3 as against 143.2 and 128.2, respectively. Live weight and wool yield in progeny of the experimental group was higher than that in the controls. Card 2/2 BOGOILYMBOV, A.'.,'.; Kii.7FITS'Y'N.A,~1 SOCiLl"'VAEOV, Using combined geophysical methods during prcsoectin.r for mineral waters in Dzhetyoguz. Sov. geol. 7 no.10:141-150 0 164. (INIRA 17: 11) 1. Vse.--oyuznyy r..,aiiclino-issledo-,ratellskiy institiit razvedochnoy geofiziki. LOVACHEVA, G.;-KUNIT STF49- S- - - - Speoification of ingredients is needed. Obshchestv. pit. no.U223 N 61. (MM 15:2) (soups) K IVI.I., vrach IINITSYTIA '~' A. , dotsent; T-TEMOV, Uze of the cytological method in the dlagno~!is of es-of-hageal cancer. Sbor. nauch. rab. S'ar, gos. med. inst. 44:260-266 764. I. 1z fa!~-.~~tet,*koy khir rfiche,,~koy k2iniki (zav~ - ro P -,,,~-.dit.Mnskogo Int-,,tit-ula (rellftor 11.1Z. Tvalic)v.). Tilt'- tovi anal of ethur-o:cyion narconi,, in -,urgical clinle. for candid.Ac. of z, 5--,lical -,~cienccc C'nair :)f the o-*:' .urFe-y (he:.tl, prof. .~O;-Iov yLn) S ara-tD v MledicLl KWITS*fliA, T.A. (Saratov, ul. Shevchenko, d. 31, kv. 1) Diagnosis and treatment of extrapulmonary intrathoracic tumors. Vest.khir. 81 no.11:99-104 N '58. (MIR& 12:3) 1. Is fakul'totakoy khirurgicheakoy kliniki imeni S.R.Mirotvor- tseva (dir. - prof. I.M.Popovlyan) Saratovskogo meditainakogo instit-ata. (CHEST--TUMORS) 11!111 f tt~ uIJ14, 1---- 1. macnmultl, i,!-, ~,P,7.c,'Tl t of n~,, u Cf--' oli---~ il-T E-,np I, agal r, I eoitj na I mmu,,tc,,moqiv foll m,"Ing -a Ibor. rau,~h. rab. Sar. r-S, mea. 8 ? 1. Iz kafedry fulcul Itatsk-c-3y khlrurlg'L-i (zav. - prof. I.M. Popol *y~tn fl, Jns-Utu'a (rek'or - N.R. P, n ov KUNITSYNA, T.A.; OLINAp I.I.; SIDELINIKOVA., YeV, Imediate and late results of sargical treatment of stomach cancer* Vopeonke 7 no*l2t7843 161* (MIRA 15:1) 1. Iz fakulltetskoy kbtrurgichesko7 kliniki (zav. - prof. I.M. Popaylyan) Saratovskogo meditsinakogo irstituta (dir. - dots. N.R. Ivanov). (STOMACH-CANCER) (STOMACH-ZTJRGERY) KWITZAR, Istvan~ dr, Modern aspects of oncological care. Repegeezeegugy 37 no.ltl5-20 Jan 56 1. Kozlemeuy a Budapest fovaros I. keruleti tanaos onkologiat gondozoJabol (rendelointozet igasgatoja: Lippe Ede dr. onkologiai gondozo fooryosa: Kunitzer Istvan dr. (NEOPIASMS, prev. & control cancer detection & prev. by pub. health workers in Hungary. diag. problems (Hun)) (PUBLIC HEALTH pub. health workeri in cancer detection & prev. in Hungary, diag. problems (Hun)) KUNIVASKPJA S. D.9 FIS117-,R L-1. Proba Neaterova pri naktoryhh zabolamliakh vmtrenrdkh organovo Vesterovia tost in certain disemos of internal organ irkh. 23s2 Km--Apr 51 P. 63-7.1 37 Teri, 1, Of thn Propedoutic Tharapeutio GlWa (Director-Profa, I. I* Tsvot1mv), Saratov Medical Institute* CWL Vol. 20, Noo 10 Oat 1951 FAMDY-DANIIL,14~11) A..; PNIFIls"14MI, M.;-jJfA.F7YFJF*,:p ~.; D"illy!lNip rc),-,tont, of froo ambio anids and pro'nin a-mUo In in rv-.irral I OaVeO Bind leUVeS W! th IMItalit C". I Oro I) !a 0 'LS. Fu' 7.10 1. -.E!3! . 12 no.5zg7l-875 3-0 165. (1-111" 19:1) 1. K,ifectrit rtmotdki Unlve-.olteta linfitil, Eltvonlm Imi-anda, Ndapeobt, ya. AERANSON, Lev Solomonovich; KOIKIN,.B.I., red., TARASOVA, T.K., m1ad. red.; YEROKHMA, L.I., tekhn. red. (Working capital of construction organizations] Oborotnye fondy stroitellnykh organizatsii. Yloskva) Ekonomika, 1964. 135 P. (MIRA 17-4) YAKOVETS, Yuriy Vladimirovich; ASTAKHOV, V.D.p red.; )M,NIKBI,,. B.~-,,, red. [Hetbo4olog'y of price determination in 'the mining industry) Metodologiia tsenoobrazovaniia v gornodobyvaiushohei pro- myshlennosti. Moskva, Ekonomika, 1964. 214 p. (VIIRA l 7 112) 1. Zaveduyushchiy kafedroy politicheskoy okonomii Leningrad- skogo gornogo Instituta, (for Yakovets). _I~NKIN, N., inzh. Suggested by the voluntary design office. NTO 4 no.11:19 N 162, (MM 16:1) 1. Byuro tekhnicheskoy informatsii Rybinskogo zavoda poligrafi- cheskikh mashin. (Rybinsk--Printing machinery and supplAos) KUIWI -111 J. N~ -. . i.w:c)~,,lalin a 1-1" 1! Cf (rutting mchines. !~4.ohJnus,roltell no.8-11 A.e. 'o,140 (MIRA !7si0l) KUNKIN, V.R.,-,-inzh.,. New designs of electric locomotives for open-pit mines. Nauch. trudy Mosk. inst. radioelek. i gor. elektromekh. no.46:51-63 162. (MIRA 17:1) -'Wz)UYANKC,, A lek-san(ir Prof I r I ye v ich -, PRIINEUKU. ?Bvej Alekw3ndrovich; Ku~!KOV, Ivan Mikhaylovich: ?0NORAREV, Alcksey Timofeye-ilch, MAID. V.R.. redaktor-, STMU10, T.V.. tek'finicheskiy racial-tor [1:xonrience in r educing Idle time of loromot ivea In repair sh-ops; the Ilannhy depot of the KrasnDyarsk Railrond] 0,3yt soki-ashcheniia ,)rostoin varovozov v rewonts: depo Ilanskals Yrasnoxarskoi -,hel6znoi dorogi. MoBkva, Gos.transp.zhel~dor, izd-vo, 1917-- V! P. (TGRii 10:13) j f (Ilanskly-Loc omot I ves-Hat nte na rice anti x,ior-ir) KUNK IN, V. IL Introducing rotary machines in plants of the Kursk Economic Council. Biul.tekh.-ekon.inform. no.10:68 160. (MIRL 13:10) (lursk-Technological innovations) ZLOBIN, V.F.;, KRIKIN, Ya.A.; 1.11LISHTF1,14, IV.A. Diamond grinding of a sectional multiclit I I OY tO()I- MasHnostroitell no.20:16-18 0 (JJLJ!~!~ 17:11) IS .1, 1 -, K'UNKIN, Ya.A.; Wil, SHTNI, V.r,.; BARANTLE, Yu.P.; TTIAYKIN, M. - ---- ---- - ---- L, Diamond grinding of small high-speed renmers. Mushinootroitell 0 no.10:20-21 0 164. (MIRA 1'1: 11) k~~V' V.F., inzhener, redaktor; KUNKIN, Ta.A., kandidat takhnichaskikh nauk, redaktor. Nechanical processing of metals; work of the Novo-Kramatorok Machine- building Plant] Makhanicheaknia obrabotka metallov; iz opyta hTAZ. Pod. red. V.F.Kopova. Kiev, Goo. nauchno-takhn. izd-vo mashinostroit. i audostroit. lit-ry [Ukr.otd-niel 1953. 49 p. (MLRA 7:6) 1. Boyo-Kranatorskiy mashinostroitellnyy mayod. (Metalwork) SXMINSKIY, V.K.; KUNKIN. YA.A. Practical application of V0A.XOIeBOT'R method in boring operationa. Stan. instr. 24 no.7:27-28 JI '53- MRA 6:8) (Drilling and boring machinery) XMIN, Ya., Imnd. tekhn. nauk; SIIKIN, A., inzh. Increasing the quality of work in overhauling ZIL-120 engines. Aft. tranSP- 36 no.l.-17-18 Ja 158. (MIRA 11:1) (Automobiles--Nnginea-Maintenance and repair) SEMIffSKIY, Vitaliy Kupriyanovich; XMR," Yakov 1bramovich; RUDNIK, S.S., -prof., red.; KUDRYAVTSEV. G., red -,t'ekhn. red. (Attachments and devices for lathe work] Prisposobleniia I instrumenty dlia tokarnoi-obrabotkis Pod red. S.S. Rudnika. Kiev, Gos.izd-vo tekhn.lit-ry USSR. 1959. 233 P. (MIRA 12:5) (Lathes--Attachments) Yakov Abramovich;- VASILENKO, Mb . red.j POSMETUKED, N.p tekhn. ie-Cle- -- [Fundamentals of machining metals on lathesl Osnovy rezaniia metal- pri tokarnoi. obrabotke. Kiev, Gos. izd-vo tekhn. lit-ry, 1961. 85 P. (Turning) (MMU 14: 11) - KUNKIN, Ya.A.y kand.tekhn.nauk Improve the technology of repairing connecting rods. Mekh. oil'. hosp. 12 no. 2:17-19 F 161. (MI&4, 14:4) (Connecting rods) .- KIJII-TKIN-..--Ya-K',, kand.tekhn.nauk; PIDGAYETSKIY, G.Ya. [PidhaietBIkyi, H.U.], - - inZ.: LEVITSIM, Sh.A. [Iovytolkyi, Sh.A.], inzh. Machinery surfaces of connecting rod joints, Mekh. sill. hosp. 32 no.9:10-12 S 161. (14IRA .14: 11) (Connecting rods) KIJNKINs Ya.p kand. tekhn.nauk Repair or-m-12 and GAZ-51 engine connecting rods. Avt.transpo 39 no-4:98' Ap 161. (HIRA 14:5) 1. U~rdortranBnii* - (Automobiles-engines) (Automobiles-14%intenance and repair) WE'lll-, - Ya. l~andetekhn.nauk; 1'(jDG,.v- '.[.--YIY, G. , inzh.; I,:,,IIITS,.IY, Sh., irlzh. Macrining surfaces of cornaact-ng rod Joints. Avt.transp. Y, nc.10:2~-30 0 '0'l. (1-1,IRA 14:10) (..1illing machines --Attaclzents KUNKIN, Ya.A.j, kand. tekhn. nauk; FAYN, L.S.,, inzh. Bench for simultaneous drilling of holes in the end of a connecting rod, Mekhe oil'. hoop, 12 no.12:7-9 D 161. (MIRA 17:1) KLINKIN) Ya.A., kand. tekhn. nauk; :'Y3,1'ISK'IY, V.A., inzh. . - Diamond lapping of boring heads for machining tractor engirie sleeves. Mashinostroenie no.3:22-24 Mly-Je 164. OMIRA 17: 11) KUNK1N,_ Xa.A., kand.tekhn-nauk; MILISHTEYN, M.Z., kand.tekhn.nauk; RYBITSKIY, V.A., kand.tekhn.naul, Efficiency of diamond machining of hard-alloy cutters. Mashinostroitell no-3:18-19 Mr 165. (~IIRA 18:4) KTJNKjN,Ya'J'-- nhuk, MUNNIKp Yu.P., lnzh.~ MIKIIEP-SON, S.Ya., i--4, -, J n 7 t, ~ Fine dJamond grInding ct' tho CurV~jAjjear surface of a hardened stee.1 car, disk. Maohimstroenle FY-Je 165. .WIFA 18,.6) Ya.A., kand. tekhn, nauk; BARANNIK, Yu.P.; YlIKHELISON, S.Yeaz Using synthetic diamond paste in lapping hnlcs, Ma2hinostraitull no.9:41 5 165. (MIll 18:12) uchitellnitsa shkol PSSR, lichnaya (White Russia--Rural conditions) MINO, V. M. (Lipen', Bobruyskiy rayon) A mother of guerrilla fighters. Rab. i sial. 39 no.2:74 F 163. (MIM 16:4) (Bobruysk District-World War, 1939-1945-Underground movements) DANTSIS, Ya.B., kand.tekhn.nauk; ZHILOV, G.M.; KUMM, E.I.., inzh. Current distribution in the flexible conductors of large ore- smelting furnaces. Vest.alektroprom. 32 w.2:58-64 F 161. (NMA 15:5) (Electric furnaces) PAI,OLU47 S.A., profe; KIJNKUflADZIIYAN, V.A., ndadshiy nauchryy sotrudnik; GEVURKYkip L.S.- ~-- ~ -- I I Urect of some antiseptic substancoa on the ascitie E~xhchls tmor. Vop. rad-iobiol. JAN Arm. SSRJ 3/4:293-2.99 1 t)). t-m-LRA 1'/:b) KUN r0T, , V'3rf~(-,r . rir.,, kozopi3koiai tanar (Bud ripwi t' ) Ult.;ioiLo limits of tho P08,13LI)MUOS Of I;f)ItC0fIIh!ht. ttd kOZ1 9 nc..I:1cj--18 Ja 165. KUN:,,,P-TI, b~Wrton Nterminant,jinand its applications. Mat lapok 13 no,3-41. 298-310 1620~ KUNPAP, E_!j SILLAMAA) H., kand. tekbn. nauk, retsenzent; ABO, L., red.; A., tekhn. red. [Automatic control] Automaatreguleerimine. Tallinn, Eesti 11iiklik Kirjastus, 1960, 279 p. [In Estonian] (MIRA 15:1) (Automatic control)