MONORAD MAINTENANCE AND OPERATOR'S MANUAL

• Document Type: CREST
• Collection: NGA Records (Formerly NIMA)
• Document Number (FOIA) /ESDN (CREST): CIA-RDP78B04770A001400010034-0
• Release Decision: RIPPUB
• Original Classification: K
• Document Page Count: 4
• Document Creation Date: December 28, 2016
• Document Release Date: January 12, 2005
• Sequence Number: 34
• Content Type: REGULATION

Approved For Release 2005/02/17 : CIA-RDP78BO477OA001400010034-0
Declass Review by NGA.
Approved For Release 2005/02/17 : CIA-RDP78BO477OA001400010034-0
 AT
AT
S AT
IAT
STAT
Approved For Release 2005/02/17 : CIA-RDP78B04770A001400010034-0
OPERATOR'S MANUAL
The purpose of the MonoRad is to facilitate and improve the process
of aligning stereo imagery viewed through a microstereoscope.
Functionally, MonoRad superimposes both output images of an anamorphic
system into a single image which may be viewed through the eyepieces
designated below.
1. The Anamorphic Eyepiece Prototype for use
on the Zoom 70 Microstereoscope equipped with = 10X wide
field eyepieces.
2. The I ladvanced anamor hic eyepiece prototype for use on the
Zoom 70 equipped with 10X wide field eyepieces.
3. The advanced anamorphic eyepiece for use on the = High
Power Stereoviewer equipped with II 6X compensating eye-
pieces or ~10X compensating, wide field, high point
eyepieces.
STAT
STAT
STAT
To interface MonoRad with the equipment listed above, three (3)
pairs of adapters are provided. The adapters have been coded 1, 2,
and 3; a card in the MonoRad case lists the corresponding anamorphics.
Approved For Release 2005/02/17 : CIA-RDP78B04770A001400010034-0
 ^
^
Approved For Release 2005/02/17 : CIA-RDP78B04770A001400010034-0
Before placing MonoRad on the anamorphics (with eyepieces removed)
screw on the correct pair of adapters. Holding MonoRad in both hands,
about its center, enables adjustment of the interpupillary distance.
One can now put MonoRad on the anamorphics. MonoRad may be oriented
in either one of two ways on the anamorphics, operatively it will give
the same result. Select the best way for operational comfort and make
sure the adapters are properly seated. One of the eyepieces used on
the anamorphics may be located in the eyepiece holder of MonoRad.
Since there are two sizes of eyepieces, two holders are provided.
The images that were in the anamorphic eyepieces are now superimposed
in the single eyepiece of MonoRad. The eyepiece may be focused by
rotating the holder in which it rests. If there appears to be a
difference in focus of the superimposed images, rotate one of the
fine focus knobs on the side of MonoRad. The fine focus knobs on the
sides of MonoRad adjust focus for the similar side on the anamorphics.
Adjustment of the images by the anamorphics or of the film by stage
motion may now be made.
After use, replace MonoRad in its case and remove the anamorphic eye-
piece.
Approved For Release 2005/02/17 : CIA-RDP78B04770A001400010034-0
 a
Approved For Release 2005/02/17 : CIA-RDP78BO477OA001400010034-0
MAINTENANCE MANUAL
The only maintenance required for MonoRad is the periodical cleaning
of the adapter lenses. The main bearing in MonoRad is made of
teflon and should not be lubricated.
MonoRad is a selaed unit and should not be disassembled. If the
unit is non-functional, it should be returned to the factory for
repair.
Approved For Release 2005/02/17 : CIA-RDP78BO477OA001400010034-0